Control Systems


MILLPWRG2 Recovery Drive and Software Compatibility

  • Due to hardware differences the original MILLPWRG2 console and the current console require different software upgrade paths.
  • Consoles can easily be identified by the color of the front bezel. The current design has a darker grey color than the original design.
    • The current G2 console will proceed to release 5 (R5) and all its service packs.
    • The original G2 console will remain with release 4 (R4) and all of its service packs.
  • To verify your software version, from the DRO screen press Setup. If you have a softkey labeled More Commands you have Release 1 software. If you have a softkey labeled Install Setup press this key.  Enter the password 8891 and press Enter.  The installed software version will be displayed at the bottom left of your screen.
  • Scroll to “Extras” at bottom of page for offline software details, previous release notes, instructions and software.

 

MILLPWRG2 Console: ID#1113777-NN

pdf MILLPWRG2 Software release Notes R6 (Update 10/2017)

pdf MILLPWRG2 Software release Notes R5-SP2 (Update 07/2017)

pdf MILLPWRG2 Software release Notes R5-SP1 (Update 02/2017)

pdf MILLPWRG2 Software release Notes R5 (Update 01/2017)

MILLPWR-G2_R6_Update.zip
(Updated 10/2017)

MILLPWR-G2_R5-SP2_Update.zip
(Updated 07/2017)

MILLPWR-G2_R5-SP1_Update.zip
(Updated 02/2017)

MILLPWR-G2_R5_Update.zip
(Updated 01/2017)

Off-line software
 CNC_MILLPWR_Off-Line_Installer.exe (Updated 10/2017)*

 

Read me first!

  • Download and read the release notes for software update instructions prior to updating to any software version.
  • R5 cannot be installed unless you have R4SP4 installed first. If you have previous version of software such as R1, R2, or R3 SPx (release 1, release 2, or release 3 with any service pack) download and install R4 SP4 prior to updating to R5.
  • Due to the enhanced features of release 5, it has become necessary to restructure the console’s hard drive. USB Recovery Drive ID# 680480-04 is now included in Recovery Drive Kit ID# 1127022-01 which supports all G2 consoles and all software versions to date or planned for the near future. This new recovery drive includes an option for resizing the control’s hard drive partitions. This must only be performed on current consoles (ID#1113777-NN) that are running software release 4 service pack 4 (R4 SP4). Please insure the console is updated to this release prior to restructuring the drive and installing release 5 (R5). Hard drive restructuring is required on these consoles prior to the upgrade to release 5 (R5).
  • Recovery Drive Kit ID# 1127022-01 can be purchased from your local ACU-RITE distributor.

 


MILLPWRG2 Console: ID#745604-NN

pdf MILLPWRG2 Software release Notes R4SP6 (Update 07/2017)

pdf MILLPWRG2 Software release Notes R4SP5 (Update 02/2017)

pdf MILLPWRG2 Software release Notes R4SP4 (Update 10/2016)

MillPWR-G2_R4-SP6_Update.zip
(Updated 07/2017)

MillPWR-G2_R4-SP5_Update.zip
(Updated 02/2017)

MillPWR-G2_R4-SP4_Update.zip
(Updated 10/2016)

Off-line software
 CNC_MILLPWR_Off-Line_Installer_R4-SP6.exe (Updated 07/2017)*

 

Read me first!

  • Download and read the release notes for software update instructions prior to updating to any software version.
  • These consoles CANNOT be upgraded to R5 and will continue to receive service packs under the R4 release. Please do not attempt to install release 5 (R5) onto these consoles.
  • System drive restructuring on this original design consoles will cause the console to become un-operational and require in house service to correct the issue. Do not restructure the drive on these consoles.
  • Not all software enhancements will be included in future R4 releases. We will continue to support console ID# 745604-NN with service packs through the R4 released software that will mainly include minor enhancements or fixes.
  • USB Recovery Drive Kit 1201909-01 includes a compatible USB Recovery Drive ID# 680480-03 for original G2 consoles (ID#745604-NN) and should be ordered when replacing a recovery drive for these consoles. This drive does not include the restructuring option, so the unit cannot be restructured accidentally.

 


 

Extras

*MILLPWRG2 Offline Software

To run the offline software a purchased KEY is required. Contact your authorized ACU-RITE MILLPWRG2 Distributor to place an order.If installing a network USB KEY follow these instructions:

Off-Line Simulator
The off-line software provides a convenient way to write part programs and simulate machine behavior using a standard Windows® computer. Features and functionality are virtually identical to that of the MILLPWRG2 control itself.

System Requirements

  • Platform: IBM compatible PC.
  • Operating System: All 32-bit and 64-bit editions of ** WINDOWS VISTA/7/8/8.1 are supported.
  • Available Drive Space: 2GB or higher.
  • Memory: 1GB or higher.
  • Display Resolution: 1024×768 (XGA) or higher required. 1440 x 900 (WXGA+) recommended.
  • Ports: One available USB port for protection device.
  • Peripherals: Keyboard and pointing device.

***Microsoft®, Windows® and Vista® are registered trademarks of Microsoft Corporation in the United States and/or other countries.

 

MILLPWR Control System for 2-axes milling applications

Serial numbers 9605-0134 through 9903-xxxx

 

MILLPWR Control System for 2/3-axes milling applications

Serial numbers 9904-xxxx and higher

 

MILLPWR Remote Storage Software

MILLPWR Remote Storage v1.1.0

 

Previous MILLPWR Control System Downloads

MILLPWRG2 Software Release Notes and Update Instructions

 

MILLPWRG2 Software Releases

Download and read the release notes for software update instructions (above) prior to updating to any software version.

NOTE: R4-SP3 is an update only. If you are running an older version of software you must first update to R4-SP1 which was a complete software update, then install R4-SP3.

To verify your software version, from the DRO screen press Setup. If you have a softkey labeled More Commands you have Release 1 software.  If you have a softkey labeled Install Setup press this key.  Enter the password 8891 and press Enter.  The installed software version will be displayed at the bottom left of your screen.